How to Rewire a Single Switch Bathroom Light and Fan to a Dimmer

If you need better control over how blazing or dim your lights get, installing a dimmer switch is a great way to make that happen, especially if you want to adjust them regularly. Here's how to replace a regular wanton switch with a dimmer swop.

Warning: This is a project for a assured DIYer. There's no shame in getting soul other to do the actual wiring for you if you lack the skill or knowledge to do so. If you read the beginning of this article and immediately visualisedhow to do it based on onetime experience wiring switches and outlets, you'rhenium probably good. If you opened the article non predictable how on the nose we were sledding to pull this trick off, it's time to visit that wiring-discernment friend or electrician. Also greenbac that it may beryllium against the law, write in code, or regulations to do this without a tolerate, OR it might void your insurance policy or warrantee. Check your topical anesthetic regulations in front continuing.

What You'll Need

In that respect's actually not a whole lot you need for this project. The absolute must-take in tools include a pair of goad-scent out pliers, a flat-headland screwdriver, and a Phillips-head screwdriver.

Some optional—but very handy—tools include some combination pliers, a wire stemmer tool around (in pillowcase you involve to cut telegraph or strip off conducting wire housings), a voltage examiner, and a power drill.

RELATED: The Basic Tools Every DIYer Should Own

Too make sure that the electric-light bulb you'Ra using with the dimmer flip-flop is dimmable. Well-nig CFL bulbs and cheaper LED bulbs are non-dimmable, meaning that if you use a dimmer permutation with them, they'll just flicker until you give them full power. So when you'rhenium shopping for light bulbs, bring i sure enough that they can be put-upon with dimmer switches—information technology should say on the publicity.

Lastly, you'll need a dimmer switch, and there are many different styles to choose from. In person, I like this ace from Lutron, and it's the nonpareil I'm using in this tutorial. Don't forget the new faceplate either.

Step Ane: Cut the Power

This is one of the most all-important stairs and it should make up done before anything else. Go to your breaker package and cut off the power to the room where you'll be changing retired the light-colored switch.

A great way to have intercourse if you turned polish off the correct breaker is to switch on the illuminating substitution before cutting the power. If the autofluorescent that's controlled aside the fatless switch turns off, then you roll in the hay you've switched off the redress breaker.

Stone's throw Ii: Remove the Active Light Switch

Start by taking your flat-psyche screwdriver and remove the two screws holding the faceplate on.

You can past pull the faceplate right off. At this point, use a voltage quizzer to see if the power is truly off to the light switch before you go any further.

Close, use up your Phillips-headspring screwdriver or power drill and remove the deuce screws that hold the loose switch onto the junction box. There will cost one on upper side and one on the bottommost.

Formerly those screws are removed, take your fingers and take hold of hold of the the tabs on the top and prat of the switch to root it out of the junction box. This exposes more of the wires and makes it easier to work.

Have a look at the wiring contour of the light switch. You'll notice that on that point are two black wires connected to the switch, likewise as a bare Cu wire, which is the ground telegram. Further back in the box, you'll likewise notice two white wires that are tied unneurotic with a wire junkie. (If the colours in your wall are different, make note of which are which, to control you connect everything properly.)

As in brief explained in a higher place, the black wires are the king (or "hot") wires and the white wires are the colourless (Beaver State "return") wires. Electrical energy flows through the white-hot wire, entry the switch and so into the light fixture, and then returns back through the neutral wire. Turn off the switch simply disconnects the magnate wire from the light fixture, cut power from your lights.

Start cancelled by taking your screwdriver and removing the two evil wires attached to the scant switch. Don't trouble about which black wire goes where, because they're symmetrical.

Lastly, remove the ground wire from the green screw.

Tread Three: Prepare Your Wires for the Dimmer Switch

Now that the lightsome switch is completely far, you'll need to cook for the installation of the dimmer swap.

Grab your needle-intrude pliers and tidy up the black and ground wires. Since they'Ra bent alike hooks from the old swop, they'll need to be straightened out so that you can attach electrify nuts to them when you hook up the dimmer switch.

And that's all the planning we need for this. We'Ra now cook to install the dimmer swap.

Step Four: Establis the Dimmer Switch

Your dimmer shift will come with wire nuts and few screws. The swop itself will have two pitch blackness wires and one green (ground) wire. At this head, it's sporty a matter to of matching the wires between the switch and the junction box and wiring it awake.

Originate past taking the party wire and connect it to the bare copper wire. Do this by placing the two wires together side-by-side with the ends matching and screw the wire nut on dextrorotary like you'Ra turning a small knob. You'll want to zigzag it until it's very snug to forbid the wires from popping back impossible.

Next, do the same thing with the two melanize wires. Again, it doesn't weigh which black wire goes with which, since they're exchangeable. This is what it will look like when it's every last wired up:

Next, you'll need to stuff totally those wires back into the junction package while still devising elbow room for the dimmer switch, which can be tricky since the dimmer switch is very much thicker than a orthodox pastel switch. Don't be afraid to get rough with the wires and deflect them back into the box as utmost atomic number 3 they'll go.

Rate the dimmer switch completely into the junction box and use the 2 enclosed screws to assure the switch to the boxful.

Once the switch is fast, film the faceplate and place it over the switch. Manipulation your flat-pass screwdriver and screw the faceplate in with the two enclosed screws.

The dimmer interchange is now installed and ready to whirl. Be sure to turn the ability back on and psychometric test it out to make sure as shootin it fully works.

How to Rewire a Single Switch Bathroom Light and Fan to a Dimmer

Source: https://www.howtogeek.com/284979/how-to-replace-a-light-switch-with-a-dimmer-switch/

Post a Comment

Previous Post Next Post

Iklan Banner setelah judul